PDA

View Full Version : Update: Aircraft Uncontroalable



Dudleigh
07-04-2006, 11:19 AM
Just updated from OOB 303m to 404m. Paid attention to D/L in correct order. All works except the aircraft are all uncontroalable. All control inputs are working, but I will eventually loos control. I had this problem when I first started and received in correct parameters to enter in the config file which are as follows:

X=0 1 4 9 16 25 36 49 64 81 100 0
Y=0 1 4 9 16 25 36 49 64 81 100 0
Z=0 10 20 30 40 50 60 70 80 90 100
RZ=0 10 20 30 40 50 60 70 80 90 100 0
FF=0
U=0 10 20 30 40 50 60 70 80 90 100 0
V=0 10 20 30 40 50 60 70 80 90 100 0
1X=0 0 0 0 13 30 46 59 70 84 100 0
1Y=0 0 0 0 13 30 46 59 70 84 100 0
1Z=0 35 41 48 56 67 76 82 89 95 100 0
1X1=0 13 21 28 39 53 65 77 88 96 100 0
1Y1=0 22 28 37 45 54 65 77 88 97 100 0
1RX1=0 10 20 30 40 50 60 70 80 90 100 0
1RZ1=0 100 100 100 100 100 100 100 100 100 100 0
1U1=0 100 100 100 100 100 100 100 100 100 100 0
1V1=0 100 100 100 100 100 100 100 100 100 100 0

I use the Saitek 45 with CH pedals
QUESTION: Has this now changed with the updates?

and Ideas ?

Denis

Dudleigh
07-04-2006, 11:19 AM
Just updated from OOB 303m to 404m. Paid attention to D/L in correct order. All works except the aircraft are all uncontroalable. All control inputs are working, but I will eventually loos control. I had this problem when I first started and received in correct parameters to enter in the config file which are as follows:

X=0 1 4 9 16 25 36 49 64 81 100 0
Y=0 1 4 9 16 25 36 49 64 81 100 0
Z=0 10 20 30 40 50 60 70 80 90 100
RZ=0 10 20 30 40 50 60 70 80 90 100 0
FF=0
U=0 10 20 30 40 50 60 70 80 90 100 0
V=0 10 20 30 40 50 60 70 80 90 100 0
1X=0 0 0 0 13 30 46 59 70 84 100 0
1Y=0 0 0 0 13 30 46 59 70 84 100 0
1Z=0 35 41 48 56 67 76 82 89 95 100 0
1X1=0 13 21 28 39 53 65 77 88 96 100 0
1Y1=0 22 28 37 45 54 65 77 88 97 100 0
1RX1=0 10 20 30 40 50 60 70 80 90 100 0
1RZ1=0 100 100 100 100 100 100 100 100 100 100 0
1U1=0 100 100 100 100 100 100 100 100 100 100 0
1V1=0 100 100 100 100 100 100 100 100 100 100 0

I use the Saitek 45 with CH pedals
QUESTION: Has this now changed with the updates?

and Ideas ?

Denis

MonkeyHero
07-04-2006, 11:23 AM
Add a 0 to the end of the Z line there. That will help some, but I'm guessing a large part of your problem is just not being used to the large flight model changes between 3.03 and 4.04. Give it some time and you should adjust.

FoolTrottel
07-04-2006, 12:26 PM
Can't tell from those numbers which is for the X-45 and which is for the pedals.

You may wan't to try the utility in my sig, it'll make it much easier for you to change them settings... It does come with some profiles, you can just try 'm...

Oh, and surely what the MonkeyH said: It needs time to get used to, but it does start with correct sensitivity settings... (As in: well, not too extreme ones. Me thinks: 1X=0 0 0 0 13 30 46 59 70 84 100 0 is a bit extreme)

Have Fun!

Dudleigh
07-04-2006, 02:17 PM
Thanks for the quick replies: Monkey maybee your right, I wasn't aware the flight models had changed: and "Fool" thanks I will certainly look over your sig


Denis

steve_v
07-04-2006, 02:59 PM
your rudder/pedals seem extreme

1Z=0 35 41 48 56 67 76 82 89 95 100 0


yaw and pitch seem resonable at

1X1=0 13 21 28 39 53 65 77 88 96 100 0
1Y1=0 22 28 37 45 54 65 77 88 97 100 0

you might want to review http://www.airwarfare.com/tech/sticks.htm

Freelancer-1
07-04-2006, 07:37 PM
Don't know if this will help, but here is mine.

Not a 45, but a 52 with Ch pedals. Maybe a little agressive for an X-45, but it's a place to start.

[rts_joystick]
X=0 1 4 9 16 25 36 49 64 81 100 0
Y=0 1 4 9 16 25 36 49 64 81 100 0
Z=0 10 20 30 40 50 60 70 80 90 100 0
RZ=0 10 20 30 40 50 60 70 80 90 100 0
FF=0
U=0 10 20 30 40 50 60 70 80 90 100 0
V=0 10 20 30 40 50 60 70 80 90 100 0

1X1=0 65 72 79 86 93 100 100 100 100 100 0..............Aileron
1Y1=0 65 72 79 86 93 100 100 100 100 100 0..............Elevator
1Z1=0 100 100 100 100 100 100 100 100 100 100 0.........Throttle
1Z=0 72 78 83 87 93 96 99 100 100 100 0.................Rudder
1RY1=0 1 4 7 13 20 29 40 52 66 81 0.....................Trim Aileron
1U1=0 1 2 4 10 14 21 29 37 47 53 10.....................Trim Elevator
1RX1=0 1 4 6 11 16 23 32 42 53 66 0.....................Trim Rudder
1Y=1 0 0 0 13 38 64 88 100 100 100 0....................Brakes